XPRO — Custom-Fit 4K Dash Cam for Toyota Corolla & C-HR
Get a Free XPRO — Toyota Corolla & C-HR Owner Program
Factory Fit for Two Toyotas. Flagship 4K in Both.
XPRO comes in two vehicle-specific housings: the 2021 Toyota C-HR and the 2023 Toyota Corolla SE Hatchback. Select your fitment above — the shells are not interchangeable, though the camera and feature set are. Each replaces the factory mirror cover, draws power from the connector behind it and leaves no cable in sight.
The camera records true 4K from Sony STARVIS 2 imaging, backed by official Sony authorization, the moment the car powers up, and clips are ready in the AKEEYO app. Optional GPS and a hardwire or OBD lead add route logging and parking protection.
约4分钟即可完成简洁、量身定制的安装。
拆下原装后视镜外壳，连接随附的电源适配器，然后将XPRO安装到位。标准行车记录无需钻孔、切割、接线或保险盒布线。
安装时间由经验丰富的AKEEYO安装人员测量。实际时间可能因车辆和安装经验而异。
三个安装步骤
1. 拆下原装外壳
使用随附的装饰工具轻轻拆下原装后视镜外壳。
2. 连接并隐藏
将随附的电源适配器插入后视镜附近的接口，然后将线缆整齐地收纳进XPRO外壳内。
标准行车记录时，无需将电源线沿着挡风玻璃或A柱布置。
3. 安装XPRO并确认录制
将XPRO对准原后视镜区域，并用力按压到位。
启动您的RAV4，通过AKEEYO应用连接，并确认摄像头画面和录制状态。
看看它有多简单。
观看完整流程——从拆除原后视镜外壳到确认您的第一次录制。
前后对比
还需要停车保护吗？
标准行车安装无需对车辆进行永久性改装。可选停车监控需要ACC降压线或OBD电源线。
ACC降压线
连接保险丝盒，实现隐蔽的停车供电。
OBD电源线
连接OBD-II接口，即插即用，安装更简单。
Made for Your 2021 C-HR.
XPRO replaces the mirror-base cover in your 2021 C-HR, so the lens, wiring and recorder sit inside the housing instead of hanging across the dash. The 8-inch display, slim A-pillars and driver-focused MeZONE cabin stay exactly as Toyota designed them - and the original cover goes back on any time.
- True 4K · officially authorized Sony STARVIS 2 IMX678
- Moulded for the 2021 C-HR mirror base - no loose cables across the sculpted dash
- Plugs into the mirror connector · fully reversible, no splicing
4-Minute Install. Factory-Fit Finish.
1Remove the Original Cover
Release the factory clips with the included trim tool. Keep the cover — it reinstalls any time.
2Plug Into the Power Connector
No cutting, no splicing — XPRO draws power from the connector behind the mirror.
3Snap On and Align
The housing clips on in the factory position. Align, press, done — fully reversible.
See How Simple It Is.
See It Record. Not Read About It.
Clearer Detail Across Changing Light.
Sony STARVIS 2 IMX678 · true 4K · F1.08 aperture · HDR — plates, signs, and vehicles stay readable through dark roads, tunnels, and oncoming glare.
Headlights under control
No white flash at the exit
Keep Watch After You Park.
With an optional ACC Hardwire Kit or OBD Power Cable, XPRO keeps recording while the car is parked — and locks the clip the moment an impact is detected.
Parked and protected
Review from the app
Review and Save Clips From Your Phone.
Connect to the AKEEYO app to preview footage live and save clips straight to your phone. Dual-band Wi-Fi delivers downloads up to 20 MB/s — so a 1-minute clip is on your phone before you finish unbuckling.
Five Safeguards, Fitted to a C-HR / Corolla SE Hatchback.
Every 2021 C-HR/ 2023 Corolla SE Hatchback. left the factory with Toyota Safety Sense 2.5. XPRO adds 4K recording without changing that cabin: impact protection, GPS, loop recording, voice alerts and voice control stay out of sight behind the mirror.
Loop Recording
Oldest unlocked footage overwrites automatically. Recording never stops.
GPS TrackingOptional module
Route, speed, and location recorded alongside your footage.
G-Sensor Protection
A sudden impact is detected by the built-in G-sensor, and the current clip is locked before loop recording can overwrite it - useful evidence whether you are threading the C-HR through city traffic or leaving it parked overnight.
Voice Alerts
Spoken status alerts keep you informed without taking your eyes off the road.
Voice Control
Voice commands for snapshots and clip protection — hands stay on the wheel.
Custom Fit Without the Usual Trade-Offs.
A factory-style housing against a universal stick-on unit and a typical vehicle-specific camera - compared on the points that matter in a 2021 C-HR / 2023 Corolla SE Hatchback.
| XPRO for 2021 C-HR / 2023 Corolla SE Hatchback | Universal Dash Cams | Typical Vehicle-Specific Cams | |
|---|---|---|---|
| Installation | Replaces mirror housing · 4 min | Suction mount, visible cables | Clean, varies by brand |
| Look | OEM-style housing | Add-on box on the windshield | Clean, varies by brand |
| Sensor | Sony STARVIS 2 · HDR | Entry-level sensor | Mixed, often older |
| Resale | Fully reversible | Adhesive residue | Reversible, varies |
Built for the Heat Inside the C-HR's MeZONE Cabin.
A parked cabin can become punishingly hot. XPRO uses an automotive-grade supercapacitor and a six-layer ENIG circuit board to stay stable through heat, cold, vibration, and years of daily driving.
No Conventional Lithium Battery.
Tolerates temperature extremes where lithium cells swell and fail, and still supplies backup power for a clean, safe shutdown.
Built for Stable, Long-Term Operation.
A six-layer ENIG board resists oxidation and corrosion, so connections stay solid through years of heat cycles and vibration.
The Numbers Behind the Picture.
One flagship 4K platform across the XPRO range - with a housing made for the 2021 Toyota C-HR mirror base. Toyota fitted Safety Sense 2.5 to every 2021 C-HR, so we ask for a photo of the mirror base and the windshield area around it before confirming a fit.
| Image Sensor | Sony STARVIS 2 IMX678 · officially authorized by Sony |
|---|---|
| Resolution | True 4K · 25 fps |
| Aperture / View | F1.08 · 107° wide angle |
| HDR | Yes — glare and tunnel exit handled |
| Wi-Fi | Dual-band 2.4 / 5.8 GHz app |
| GPS | Optional module |
| Storage | Built-in 64GB · supports up to 256GB |
| Power | Supercapacitor · −20°C to 70°C |
Questions, Answered Straight.
Fitment, power, installation and everyday recording - the questions we hear most often about fitting XPRO to a 2021 C-HR / 2023 Corolla SE Hatchback.
Will XPRO fit my 2021 Toyota C-HR /2023 Corolla SE Hatchback ?
XPRO on this page is designed for the 2021 Toyota C-HR /2023 Corolla SE Hatchback. Toyota made Safety Sense 2.5 standard on every 2021 C-HR, and grade names differ by market - LE, XLE, Limited and Nightshade in the US. Because the mirror-base cover and the equipment around the windshield can vary, please send a clear photo of the plastic housing behind your rearview mirror, with your model year and trim, to help@akeeyo.com before ordering and we will confirm the fit.
How long does installation take?
Around four minutes: release the housing clips, seat XPRO, connect the plug. No splicing, no adhesive.
Does it work while parked?
Yes — with the optional ACC Hardwire Kit or OBD Power Cable, impact detection locks footage while parked.
Three things worth checking on a 2021 C-HR /2023 Corolla SE Hatchback .
No guesswork on fitment, no irreversible changes to the car, and a support team that can look at your mirror cover before you buy.
Photo fitment check
Toyota made Safety Sense 2.5 standard on every 2021 C-HR. Send a clear photo of the mirror base and the windshield area around it, with your model year and trim - LE, XLE, Limited or Nightshade in the US - and we confirm the housing before you order.
Fully reversible install
The housing clips into the factory position and unplugs. No adhesive on the windshield, no permanent modification.
No cutting or splicing
Power comes from the connector behind the mirror. The factory wiring stays untouched.
Factory Fit. Flagship 4K. Zero Compromise.
Install in four minutes this weekend. Drive with a witness you will never notice.